Phil Hobbs <pcdhSpamMeSenseless@electrooptical.net>wrote:
https://hackaday.com/2026/11/17/newer-rigol-scopes-get-a-custom-linux-firmware/
Looks pretty cool, and runs off the built-in SD card, so you can switch
back to the factory software anytime.
Cheers
Phil Hobbs
Phil Hobbs <pcdhSpamMeSenseless@electrooptical.net>wrote:
https://hackaday.com/2026/11/17/newer-rigol-scopes-get-a-custom-linux-firmware/
Looks pretty cool, and runs off the built-in SD card, so you can switch
back to the factory software anytime.
Cheers
Phil Hobbs
Impressive!
Jan Panteltje <alien@comet.invalid> wrote:
Phil Hobbs <pcdhSpamMeSenseless@electrooptical.net>wrote:
https://hackaday.com/2026/11/17/newer-rigol-scopes-get-a-custom-linux-firmware/
Looks pretty cool, and runs off the built-in SD card, so you can switch
back to the factory software anytime.
Cheers
Phil Hobbs
Impressive!
It?s clearly not ready for prime time yet, but if the guy keeps cranking on >it, it might be pretty useful.
Simon has been using open-weight LLMs to build a bunch of lab automation >stuff, which is promising.
Cheers
Phil Hobbs
On Tue, 17 Nov 2026 17:04:44 -0000 (UTC), Phil Hobbs <pcdhSpamMeSenseless@electrooptical.net> wrote:
Jan Panteltje <alien@comet.invalid> wrote:
Phil Hobbs <pcdhSpamMeSenseless@electrooptical.net>wrote:
https://hackaday.com/2026/11/17/newer-rigol-scopes-get-a-custom-linux-firmware/
Looks pretty cool, and runs off the built-in SD card, so you can switch >>>> back to the factory software anytime.
Cheers
Phil Hobbs
Impressive!
It?s clearly not ready for prime time yet, but if the guy keeps cranking on >> it, it might be pretty useful.
Simon has been using open-weight LLMs to build a bunch of lab automation
stuff, which is promising.
Cheers
Phil Hobbs
My kids are doing astounding stuff with Claude.
I designed a high voltage pulse generator, with an LTC3803 booster
feeding a voltage multiplier in the 0-700 volt supply. A filtered PWM
from an FPGA boogers the feedback pin to set the HV level.
One of my guys pushed the schematic and Spice model into Claude and
asked it to compute his cal factors. Then he ran the board and asked
for 300 volts. He got 301.
That's terrifying. AI is unemploying coders and potentially circuit
desigers too.
What is " boogers the feedback pin"?
someone <2a59d59e3809f827ce709d3815e3950eef4a6a93af5557a93a7fdfba71460843@example.com>wrote:
The de facto leader in instrumented automation includes Rigol as a minuscule subset of their capabilities.
On Tue, 17 Nov 2026 17:04:44 -0000 (UTC), Phil Hobbs <pcdhSpamMeSenseless@electrooptical.net> wrote:
Jan Panteltje <alien@comet.invalid> wrote:
Phil Hobbs <pcdhSpamMeSenseless@electrooptical.net>wrote:
https://hackaday.com/2026/11/17/newer-rigol-scopes-get-a-custom-linux-firmware/
Looks pretty cool, and runs off the built-in SD card, so you can switch >>>> back to the factory software anytime.
Cheers
Phil Hobbs
Impressive!
It?s clearly not ready for prime time yet, but if the guy keeps cranking on >> it, it might be pretty useful.
Simon has been using open-weight LLMs to build a bunch of lab automation
stuff, which is promising.
Cheers
Phil Hobbs
My kids are doing astounding stuff with Claude.
I designed a high voltage pulse generator, with an LTC3803 booster
feeding a voltage multiplier in the 0-700 volt supply. A filtered PWM
from an FPGA boogers the feedback pin to set the HV level.
One of my guys pushed the schematic and Spice model into Claude and
asked it to compute his cal factors. Then he ran the board and asked
for 300 volts. He got 301.
That's terrifying. AI is unemploying coders and potentially circuit
designers too.
On 18/11/2026 7:24 am, john larkin wrote:
On Tue, 17 Nov 2026 17:04:44 -0000 (UTC), Phil Hobbs
<pcdhSpamMeSenseless@electrooptical.net> wrote:
Jan Panteltje <alien@comet.invalid> wrote:
Phil Hobbs <pcdhSpamMeSenseless@electrooptical.net>wrote:
https://hackaday.com/2026/11/17/newer-rigol-scopes-get-a-custom-linux-firmware/
Looks pretty cool, and runs off the built-in SD card, so you can switch >>>>> back to the factory software anytime.
Cheers
Phil Hobbs
Impressive!
It?s clearly not ready for prime time yet, but if the guy keeps cranking on >>> it, it might be pretty useful.
Simon has been using open-weight LLMs to build a bunch of lab automation >>> stuff, which is promising.
Cheers
Phil Hobbs
My kids are doing astounding stuff with Claude.
I designed a high voltage pulse generator, with an LTC3803 booster
feeding a voltage multiplier in the 0-700 volt supply. A filtered PWM
from an FPGA boogers the feedback pin to set the HV level.
One of my guys pushed the schematic and Spice model into Claude and
asked it to compute his cal factors. Then he ran the board and asked
for 300 volts. He got 301.
He should have asked for 300.00V and got it.
That's terrifying. AI is unemploying coders and potentially circuit
designers too.
Somebody who asks for 300V and is happy to get 301V isn't any kind of >potential circuit designer. It's terrifying that you didn't notice.
On Fri, 20 Nov 2026 17:07:28 +1100, Bill Sloman <bill.sloman@ieee.org>
wrote:
On 18/11/2026 7:24 am, john larkin wrote:
On Tue, 17 Nov 2026 17:04:44 -0000 (UTC), Phil Hobbs
<pcdhSpamMeSenseless@electrooptical.net> wrote:
Jan Panteltje <alien@comet.invalid> wrote:
Phil Hobbs <pcdhSpamMeSenseless@electrooptical.net>wrote:
https://hackaday.com/2026/11/17/newer-rigol-scopes-get-a-custom-linux-firmware/
Looks pretty cool, and runs off the built-in SD card, so you can switch >>>>>> back to the factory software anytime.
Cheers
Phil Hobbs
Impressive!
It?s clearly not ready for prime time yet, but if the guy keeps cranking on
it, it might be pretty useful.
Simon has been using open-weight LLMs to build a bunch of lab automation >>>> stuff, which is promising.
Cheers
Phil Hobbs
My kids are doing astounding stuff with Claude.
I designed a high voltage pulse generator, with an LTC3803 booster
feeding a voltage multiplier in the 0-700 volt supply. A filtered PWM
from an FPGA boogers the feedback pin to set the HV level.
One of my guys pushed the schematic and Spice model into Claude and
asked it to compute his cal factors. Then he ran the board and asked
for 300 volts. He got 301.
He should have asked for 300.00V and got it.
That's terrifying. AI is un-employing coders and potentially circuit
designers too.
Somebody who asks for 300V and is happy to get 301V isn't any kind of
potential circuit designer. It's terrifying that you didn't notice.
Hitting that close was mostly luck. The switcher reference and the
many resistors all have about 1% tolerances, so it might have been 10
volts off.
What astounded me is that it understood a pretty complex boost switcher+voltage multiplier+unusual control loop and generated good
cal factors. We'll of course tweak the cal factors when we test
production units.
I fiddled the design in Spice to get the resistor values and tune the
loop dynamics, which was easier than cranking out the math.
Next thing like this, I'll see if Claude can do the whole design.
On 21/11/2026 3:14 am, john larkin wrote:
On Fri, 20 Nov 2026 17:07:28 +1100, Bill Sloman <bill.sloman@ieee.org>
wrote:
On 18/11/2026 7:24 am, john larkin wrote:
On Tue, 17 Nov 2026 17:04:44 -0000 (UTC), Phil Hobbs
<pcdhSpamMeSenseless@electrooptical.net> wrote:
Jan Panteltje <alien@comet.invalid> wrote:
Phil Hobbs <pcdhSpamMeSenseless@electrooptical.net>wrote:
https://hackaday.com/2026/11/17/newer-rigol-scopes-get-a-custom-linux-firmware/
Looks pretty cool, and runs off the built-in SD card, so you can switch >>>>>>> back to the factory software anytime.
Cheers
Phil Hobbs
Impressive!
It?s clearly not ready for prime time yet, but if the guy keeps cranking on
it, it might be pretty useful.
Simon has been using open-weight LLMs to build a bunch of lab automation >>>>> stuff, which is promising.
Cheers
Phil Hobbs
My kids are doing astounding stuff with Claude.
I designed a high voltage pulse generator, with an LTC3803 booster
feeding a voltage multiplier in the 0-700 volt supply. A filtered PWM
from an FPGA boogers the feedback pin to set the HV level.
One of my guys pushed the schematic and Spice model into Claude and
asked it to compute his cal factors. Then he ran the board and asked
for 300 volts. He got 301.
He should have asked for 300.00V and got it.
That's terrifying. AI is un-employing coders and potentially circuit
designers too.
Somebody who asks for 300V and is happy to get 301V isn't any kind of
potential circuit designer. It's terrifying that you didn't notice.
Hitting that close was mostly luck. The switcher reference and the
many resistors all have about 1% tolerances, so it might have been 10
volts off.
1% of 300V is three volts. Resistor tolerances can be positive or
negative so if there were lots of resistors in the train the net effect >starts averaging out.
On Sat, 21 Nov 2026 03:57:15 +1100, Bill Sloman <bill.sloman@ieee.org>It certainly doesn't. But in any individual case it probably will.
wrote:
On 21/11/2026 3:14 am, john larkin wrote:
On Fri, 20 Nov 2026 17:07:28 +1100, Bill Sloman <bill.sloman@ieee.org>
wrote:
On 18/11/2026 7:24 am, john larkin wrote:
On Tue, 17 Nov 2026 17:04:44 -0000 (UTC), Phil Hobbs
<pcdhSpamMeSenseless@electrooptical.net> wrote:
Jan Panteltje <alien@comet.invalid> wrote:
Phil Hobbs <pcdhSpamMeSenseless@electrooptical.net>wrote:
https://hackaday.com/2026/11/17/newer-rigol-scopes-get-a-custom-linux-firmware/
Looks pretty cool, and runs off the built-in SD card, so you can switch
back to the factory software anytime.
Cheers
Phil Hobbs
Impressive!
It?s clearly not ready for prime time yet, but if the guy keeps cranking on
it, it might be pretty useful.
Simon has been using open-weight LLMs to build a bunch of lab automation >>>>>> stuff, which is promising.
Cheers
Phil Hobbs
My kids are doing astounding stuff with Claude.
I designed a high voltage pulse generator, with an LTC3803 booster
feeding a voltage multiplier in the 0-700 volt supply. A filtered PWM >>>>> from an FPGA boogers the feedback pin to set the HV level.
One of my guys pushed the schematic and Spice model into Claude and
asked it to compute his cal factors. Then he ran the board and asked >>>>> for 300 volts. He got 301.
He should have asked for 300.00V and got it.
That's terrifying. AI is un-employing coders and potentially circuit >>>>> designers too.
Somebody who asks for 300V and is happy to get 301V isn't any kind of
potential circuit designer. It's terrifying that you didn't notice.
Hitting that close was mostly luck. The switcher reference and the
many resistors all have about 1% tolerances, so it might have been 10
volts off.
1% of 300V is three volts. Resistor tolerances can be positive or
negative so if there were lots of resistors in the train the net effect
starts averaging out.
Sensible engineering doesn't assume that component tolerances will
average out.
Thinking like that kills people.
What is " boogers the feedback pin"?
| Sysop: | Jacob Catayoc |
|---|---|
| Location: | Pasay City, Metro Manila, Philippines |
| Users: | 5 |
| Nodes: | 4 (0 / 4) |
| Uptime: | 498678:28:03 |
| Calls: | 212 |
| Calls today: | 3 |
| Files: | 912 |
| D/L today: |
31 files (22,593K bytes) |
| Messages: | 69,867 |